SMITH'S 10-Second Knife & Scissors Sharpener JIFF-S
SMITH'S 10-Second Knife & Scissors Sharpener JIFF-S
SMITH'S 10-Second Knife & Scissors Sharpener JIFF-S
SMITH'S 10-Second Knife & Scissors Sharpener JIFF-S
ROSS CUTLERY

SMITH'S 10-Second Knife & Scissors Sharpener JIFF-S

Regular price $9.98 Sale price $11.98

SMTH-jiff-s

Knife Sharpener

The Smith's "10 Second" Knife Sharpener features a specially designed "V" shaped sharpening slot with two crossed carbide blades that allow you to put a quick edge on your knife with just three or four strokes. The carbide blades are pre-set so that you get the correct sharpening angle every time. They are also reversible for extended life and replaceable.

Scissors Sharpener

The Smith's Scissors Sharpener features a specially designed "FLOATING" round ceramic rod, which conforms to the exact angle of your scissors every time. It works on both left & right handed scissors. Just three or four strokes is all it takes to put the edge back on your scissors.

Features

  • "V" Shaped Sharpening Slot Ensures Proper Sharpening Angle
  • Reversible and Replaceable Carbide Blades Extend Sharpening
  • Sharpens All Types of Knives and Left or Right Handed Scissors
  • Carbides: Coarse
  • Fine Ceramic: 800 Grit

Replacement Carbide Blades can be found here.

Knife Sharpening Instructions:

Always keep your fingers inside the hand guard and your thumb securely on the thumb rest indention on the top of the sharpener; otherwise possible injury may occur.

  1. To sharpen the knife, place the knife on a solid flat surface with the cutting edge facing up. Securely hold the knife in place with downward pressure on the handle. For best results allow about 1/2" to 1" of the blade to extend past the edge of your flat surface.
  2. Starting near the handle of the knife, place the "V" in the head of the sharpener over the cutting edge of the knife. Position the head of the sharpener at a 90 degree angle to the knife's cutting edge. While holding the knife with one hand and the sharpener in the other, draw the sharpener across the blade from the heel of the point while applying light downward pressure. At the end of each stroke, continue your outward motion in order to avoid any contact with the blade. You will feel the tungsten carbide cutters removing metal from the knife. Repeat this process 3 or 4 times or until your knife is sharp.
  3. Remember light pressure is sufficient when using the sharpener. Heavy pressure might cause you to lose control of the knife and could cause possible injury.
  4. The carbide cutting heads are reversible and replaceable. When the heads stop cutting they can be rotated and used on the other side. To rotate the heads remove the screw and the plastic cover piece. Remove the carbides and rotate them 1/2 turn and then place the top carbide into the bottom slot and the bottom carbide into the top slot.

Scissors Sharpening Instructions:

The specially designed "floating sharpening rod conforms to the exact angle of your scissors. It is simple and easy to use and it works on both left- & right-handed scissors.

  1. To sharpen right-handed scissors, begin by holding the head of the knife sharpener in your left hand with the words "right- handed scissors" facing you. Then place the flat base at the other end of the handle on the solid flat surface.
  2. Open your scissors blades and insert the blades as far as possible through the slots.
  3. Close scissors on the sharpening rod as if you were trying to cut the rod, then pull the scissor blades through the slots while trying to keep the blades closed. Repeat this process 3 or 4 times (more for duller scissors). If preferred, push scissors through unit instead of pulling
  4. To sharpen left-handed scissors hold the head of the sharpener in your right hand with the words" left-handed scissors" facing you and then repeat steps 2 and 3.

Care:

Always clean your sharpener after using. Rinse with warm water and towel dry.

 


More from this collection